Development of a Learning Module to Interpret Engineering Drawings Using Augmented Reality (AR) for Vocational High School Students

Authors

  • Zuhdi Mizian Universitas Jambi, Indonesia
  • Sofyan Sofyan Universitas Jambi, Indonesia
  • Saharrudin Saharrudin Universitas Jambi, Indonesia

DOI:

https://doi.org/10.35445/alishlah.v17i2.7217

Keywords:

Learning Module, Engineering Drawing, Augmented Reality, Vocational School

Abstract

Interpreting engineering drawings is a fundamental competency for vocational high school students preparing for industrial careers. However, conventional instruction often fails due to students’ difficulty in visualizing 3D objects from 2D representations, limited interactive learning tools, and low motivation. This study aimed to develop an Augmented Reality (AR)-assisted learning module to enhance the effectiveness and interactivity of engineering drawing instruction. The research employed the ADDIE (Analysis, Design, Development, Implementation, Evaluation) model of Research and Development (R&D), involving material experts, media specialists, instructional designers, teachers, and vocational students. The developed module was evaluated for feasibility and effectiveness. Expert assessments rated the module as "Very Feasible," with scores from material experts (96.80%), media experts (77.00%), and instructional design experts (93.80%). A limited implementation trial demonstrated a significant improvement in student understanding, indicated by an N-gain score of 0.71 (high category). Additionally, 89.3% of students reported high satisfaction with the module. The findings suggest that the AR-assisted module effectively enhances students' ability to interpret engineering drawings. This development presents an innovative alternative to conventional methods and demonstrates the potential of AR integration to create engaging, interactive learning environments in vocational education settings.

References

Azuma, R., Billinghurst, M., & Klinker, G. (2011). Special Section on Mobile Augmented Reality. Computers & Graphics, 35(4), vii–viii. https://doi.org/10.1016/j.cag.2011.05.002

Branch, R. M. (2009). Instructional Design: The ADDIE Approach. Springer US. https://doi.org/10.1007/978-0-387-09506-6

Creswell, J. W., & Creswell, J. D. (2018). Mixed Methods Procedures. In Research Defign: Qualitative, Quantitative, and Mixed M ethods Approaches.

Dick, W., Carey, L., & Carey, J. O. (2015). The Systematic Design of Instruction. Vital Source (for Pearson) VST E+p. https://books.google.co.id/books?id=XIjNjgEACAAJ

Johnson, L., Adams, S., & Cummins, M. (2012). Technology outlook for Australian tertiary education 2012-2017: An NMC Horizon Report regional analysis. The New Media Consortium.

Luthfi Arfianti. (2022). DEVELOPMENT OF ENGINEERING DRAWING LEARNING MODULE FOR VOCATIONAL STUDENT AT PROPERTY CONSTRUCTION BUSINESS EXPERTISE PROGRAM. Jurnal PenSil, 11(1), 65–77. https://doi.org/10.21009/jpensil.v11i1.18950

Morrison, G. R., Ross, S. J., Morrison, J. R., & Kalman, H. K. (2019). Designing effective instruction. John Wiley & Sons.

Nieveen, N., & Folmer, E. (2013). Educational Design Research Educational Design Research. Netherlands Institute for Curriculum Development: SLO, 1–206. http://www.eric.ed.gov/ERICWebPortal/recordDetail?accno=EJ815766

Richey, R. C., Klein, J. D., & Tracey, M. W. (2010). The Instructional Design Knowledge Base. Routledge. https://doi.org/10.4324/9780203840986

Rodrigues-Silva, J., & Alsina, Ã. (2023). Systematic Review About Students’ Conceptions of Engineering Accessed Through Drawings: Implications to STEAM Education. International Journal of Cognitive Research in Science, Engineering and Education (IJCRSEE), 11(2), 199–211. https://doi.org/10.23947/2334-8496-2023-11-2-199-211

Saputra, H. N., Salim, S., Idhayani, N., & Prasetiyo, T. K. (2020). Augmented Reality-Based Learning Media Development. Al-Ishlah: Jurnal Pendidikan, 12(2), 176–184.

Sriadhi, S., Hamid, A., Sitompul, H., & Restu, R. (2022). Effectiveness of Augmented Reality-Based Learning Media for Engineering-Physics Teaching. International Journal of Emerging Technologies in Learning (IJET), 17(05), 281–293. https://doi.org/10.3991/ijet.v17i05.28613

Van den Akker, O., Weston, S., Campbell, L., Chopik, B., Damian, R., Davis-Kean, P., Hall, A., Kosie, J., Kruse, E., & Olsen, J. (2021). Preregistration of secondary data analysis: A template and tutorial. Meta-Psychology, 5, 2625.

Wang, F., & Hannafin, M. J. (2005). Design-based research and technology-enhanced learning environments. Educational Technology Research and Development, 53(4), 5–23. https://doi.org/10.1007/BF02504682

Widayana, G., Rohman, M., Sulaiman, M., & Ratnawati, D. (2020). The Effectiveness of Interactive Multimedia-based Learning in Engineering Drawing Courses. 14, 2020.

Zheng Jian. (2011). Teaching of Engineering Drawing in the 21st century. 2011 Second International Conference on Mechanic Automation and Control Engineering, 1713–1715. https://doi.org/10.1109/MACE.2011.5987287

Downloads

Published

2025-06-30

How to Cite

Mizian, Z., Sofyan, S., & Saharrudin, S. (2025). Development of a Learning Module to Interpret Engineering Drawings Using Augmented Reality (AR) for Vocational High School Students. AL-ISHLAH: Jurnal Pendidikan, 17(2), 3352–3367. https://doi.org/10.35445/alishlah.v17i2.7217

Issue

Vol. 17 No. 2 (2025): JUNE 2025

Section

Articles

Citation Check

License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.